Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Lift and support the front of the truck so the front wheels are off the ground take safety precautions, chock wheels, jack stands, etc Key on, engage 4x4 and try to turn the front drive shaft. This motor worked good on a 97 ford expedition. Or a fuse could be blown in the fuse panel under the dash or under the hood. Priced right, works great out of the box. Feb 07, 2011 The most common problem with those systems is the electric transfer case 4x4 motor mounted on the rear of the transfer case next to the rear drive shaft.
Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir. These electric shifts have a tendacy to get out of time and or just go bad. This article will cover how to replace it yourself to save you. We need to have the assembly number at time of the order it can ensure that you obtain a direct drop in replacement. If both fuses are okay, go to next step.
Allow the belt to retract. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. Step 6 - Replace the wiring harness Replace the wiring harness. Lift and support the front of the truck so the front wheels are off the ground take safety precautions, chock wheels, jack stands, etc Key on, engage 4x4 and try to turn the front drive shaft. Using voltmeter, measure voltage at terminal No.
Check the vent line tube that is routed into the engine compartment with nothing attached to it , for blockages. If voltage is 10 volts or less, go to next step. Bring the vehicle to a stop. They might be to close to the exhaust pipes. I was happily surprised when I opened this box.
A ball point pen or a narrow-tip punch can be used to disconnect the other wires that are connected to this harness. Turn control down to decrease delay. The main harness is connected via a clip. The yellow and orange were to thick even on the oem plug to remove. Have you installed a radio recently. This process will also arm your anti-theft system. As the old plug had double the wires to move.
Just a place to start. Install the child safety seat in a seating position which is capable of providing a tether anchorage. The other thing could be the connector on the transfer case is corroded, remove the connector, and check it for water and other junk, clean if necessary. Now 4x4 light comes on the second I flip the switch, and low range engages no problem when in neutral with the brake. This article applies to the Ford F-150 2011-2014. Safety belt Illuminates when the ignition is switched on to remind you to fasten your safety belts. Always disconnect the battery before servicing high current fuses.
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. I was happily surprised when I opened this box. However, in some climates, you may need to use snow tires and chains. If you are skilled enough, you can take apart the motor and replace this bushing, saving you the cost of replacing the entire motor. What else should I look for and how should I check? Follow the wires up from the t-case as far as you can.
My 2002 F-150 has the rectangular plug pictured. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. If a light fails to illuminate, have the vehicle serviced. Would save a lot of time for the install. Do not grip the spokes.
The electric shift switch could be bad. May 16, 2010 The switch could be bad, but if you cannot select 4H or 2H, I would think the shift motor in the transfer case is the issue. Your going to have to trace some wires here. The 4x4 selector changes the voltage for each function. If you had to remove extra wires from other components, be sure to replace them in the same positions they were in prior to removal. Remove the two bolts from the inside of the tailgate.
Step 7 - Reconnect the battery terminals Reconnect the battery terminals, lower the truck, and check your 4x4 function. Straighten alignment pins, making them parallel with the outer edges of the attachment standoff. We can easily exchange your current transfer case for you personally, or supply a direct drop in replacement unit shipped to your residence or commercial street address. Apply the accelerator slowly and avoid spinning the wheels. If still nothing might have happen in dash,,Lets hope thats not where to go next. To disconnect the safety belt, push the red release button and remove the tongue from the buckle.