Overall well built and well designed. All right, when you have got these screws taken out, you can pop the bumper off from the side by the fender well. If I were to install it again I could probably get it down below 1 hour. Extended warranties are also available for purchase; please call for details. Step 4 of the install guide mentions the M12 bolt on the driver's side; it is actually on the passenger's side. Using a Durametric Version 6 scanner I was able to verify the installation by using this diagnostic tool to identify the controller and run diagnostic tests. Entering your vehicle information in our Year Make Model selector up top, helps ensure you get an auto part that fits your car, truck or other type of vehicle.
Now we can go ahead and reattach the bumper cover. Needed die grinder with cut-off wheel to complete install, a tool not always available to average consumer. And then just go ahead and basically start reinstalling the screws that you took out. First thing I would check is the type of bulbs you are running. Again I do not have any experience with this method and cannot attest either way how well it works. Once removed you should see a rubber plug.
The hitch arrived within 2 days of my order. My issue occurred after the install. You will not know that until you actually take out the bolts and measure them. And it will stay there just like that. And then go ahead and do the same thing on the other tail light. First, we will make our connection for the backup sensors, and then we will pop the fascia back on. With the bumper cover off, the next thing I do is take off this steel bumper itself.
I did contact several Ebay sellers if they had the wiring harnesses and all of them said they were not available. We had to purchase a tap and die set to recut the threads in the frame of the vehicle. All right, the next thing we need to do is go ahead and take off the bumper cover. I have double checked all my connections but still not brake lights. Our host sells all the necessary hardware. And this is a heavy piece of equipment, so it is a good idea to have an extra set of hands involved. This is an uncommon tow module controller because it has the ability to control the retractable tow hitch.
Need assistance selecting the right Draw-Tite product? To my dismay the lights flickered and flashed randomly, indicating an obvious problem. This write-up was very well written with detailed photos. Although we endeavour to ensure that the information contained on the website is accurate, as errors may occur from time to time, customers should verify any information in question with a dealer. Inside the fender well here, we are going to undo these torque screws here. This can be confirmed by looking at the specs of each presented above.
I decided to go with the Factory tow module route. Remember to replace the rubber plug in the hole you passed the wiring harness through. Trailer Hitches - Draw-Tite 24847 Rating: 3 Stars Shipping was fast and I was very happy with the whole transaction. We are not responsible for any errors or omissions on this website. Part 1 of 2 I know I am not the first person to tackle this project but I wanted to share my experiences with the group while it is still fresh in my mind. At this point all that was left to do was remove panels and properly install the hardware. Fit exactly as expected slight fitment problems with the exhaust hanger on the passenger side - can be filed or drilled.
I was able to find several used tow module controllers on Ebay mostly from Europe but wiring harness were rare. And to completely take the bumper off, we need to disconnect this electrical connection here. Once this original rubber plug is removed, go underneath the corner of the car on the right passenger side and feed the pigtail that connects to the control unit through the hole. Again I do not have any experience with these products. If you need any assistance please feel free to give us a call at. Better than ebay and amazon and I'm a prime member.
After weeks of researching how to remove the side panels to no avail Wayne posted a motherlode of tech articles on this forum how to replace the rear hatch shocks. Some items may be unavailable for or incompatible with certain trim levels and models. Draw-Tite, a leading aftermarket manufacturer of top-notch towing systems, is unsurpassed in price and quality. When you take these bolts off, this is the factory bolt. Would definitely buy from them again.
Photos are for illustration purposes only. There may be some variances between the photos shown and the actual product. If you are planning to tow a trailer, for use over any distance, you should consider the condition of your tow vehicle. In addition, buying a used wiring harness has its pitfalls because you do not know how carefully it was removed. Therefore, I needed to get the appropriate electrical connections for trailer lights.