Install only one screw at this time as accumulator must be free to pivot upward for ease of installation. They are equipped with a lock-up clutch in the torque converter. . Be sure to take advantage of the sale because quantities won't last long. If tool is not seated and gear splines rotate out of alignment, over- drive unit will have to be disassembled in order to realign splines.
Fluid When the throttle valve is as far over to the left as. This transmission was Chrysler's proverbial Workhorse in modern-day pickup trucks. Then swing valve body over piston and outer spring 1 Turn valve body assembly over so accumulator to hold it in place. Make sure when you compare our kits to the competition that you take into account all of the small items we include that they do not. What is a Core Charge? Mount it on blocks, or in workbench with appropriate size mounting hole cut into it.
This transmission was Chrysler's proverbial Workhorse in modern-day pickup trucks. Replace the overrunning clutch roller and spring assembly if any rollers or springs are worn or dam- aged, or if the roller cage is distorted, or damaged. Fill Tube where tube enters case 2. Global Transmission Parts is not liable for any errors or omissions. This increased throttle pressure back up to the switch valve. This Actuator has replaced the previous Throttle Valve Cable and all associated linkage.
End play should be 0. Torque Converter Bolts Hitting 2. Be sure locating ring groove in bear- ing is toward rear. The double-wrap band pro- vides a greater holding power in comparison to the Fig. Then install remaining clutch discs and plates through gauge tool slot until scale contacts end of in same order. United States Army Drill Sergeant J. Seat washer tabs in to hold washer in place if desired.
Test and replace switch if faulty. Note the orientation of the clutch discs. Be very sure retaining ring is fully seated in sun gear ring groove. Adjust linkage - setting may be too long. The check ball is approxi- from transfer plate. Also be sure incorrectly assembled, or reaction shaft thrust fiber thrust washer is in position Fig.
We are dedicated to giving you the technical support you need, when you need it! The sensor is positioned over the park gear and monitors transmission output shaft rotating speed. Damaged threads can be Tool C-4470, or Valve Spring Compressor C-3422-B repaired with Helicoil thread inserts. They are equipped with a lock-up clutch in the torque converter. Then remove clutch pack from hub Fig. Be sure unit is facing upward for access to direct clutch hub. Then install annulus gear retaining snap- plates or drum if binding occurs. The differences internally between A518 transmissions and their larger A618 counterpart are the A618 transmissions used steel planets and A518 planetary gear sets are made from alumimum.
Verify that thrust washers, thrust plates and seal rings are correctly positioned. Damaged or worn threads in the aluminum trans- 6 Remove starter motor. The turbine is mounted within the housing opposite the impeller, but is not attached to the housing. Tighten bolts to 20 N·m 175 in. The clutch pack consists of 23 sin- gle-sided discs and they must be installed in the same orientation as they were removed. The overdrive 54-60 psi 372-414 kPa with throttle lever forward clutch pressure port is at the left rear of the case. Discard snap-ring as it is not reus- able.
Use scriber or paint to make alignment marks. If rod will not 6 Move the transmission manual shaft lever to slide past park pawl, pawl is engaged in park gear. Then clean the servo components with solvent and dry with compressed air. Verify floor mat is not under pedal, repair Restricted. The solenoids operate the valves. The 1 Hoist and support vehicle on safety stands.
Replace the driving shell if distorted, cracked, or damaged in any way. This Actuator has replaced the previous Throttle Valve Cable and all associated linkage. This kit comes with every part you need to make your transmission run at the levels of a Monster. First through third gear ranges are provided by the clutches, bands, low-roller clutch, and planetary gearsets in the transmission. Shift Better, Last Longer When it comes to transmissions, no other company provides this level of commitment to their clients.
Engine starts must be possible. Many automotive parts have a Core Charge, or Core Price, that works the same way as a soda can deposit. Note check ball location for mately 4. If clearance is incorrect, clutch plates, clutch discs, snap-ring, or pressure plate may have to be changed. The fluid pressure is them with compressed air. There is no leaking coming from the front seals, rear sears or oil pan.