Air pressure must be the same in all tires for longer life. Step-by-step instruction, diagrams, and schematic shows how troubleshoot and fix your bobcat machine easily. If none are found, disconnect the battery and disconnect the rectifier and regulator modules from the jumper harness. Buckets, Grapple Buckets, harley rakes, 4 in 1 buckets, trenchers, hydraulic augers, pallet forks, sweepers, brush cutter, stump grinders and dozer blades are all commonly used on Bobcat 610 Skid Steer Loaders. It is written in the language of a mechanic and may include valuable detailed information such as specifications, torques, ranges, etc. Use a good lithium base grease. Check the Bob—Tach attachment for condition.
Lay it face up and install clean copper element. The check valve is intended to keep water from entering engine in event engine turns over backwards opposite of normal rotation. Run engine at full throttle for 1 minute then stop engine. Remove and discard the oil filter cartridge. Remove floor panels and disconnect linkage 600 Electric and Petter diesel.
Inspect and clean vanes on air cleaner Fig. If you do your own repairs, you need the parts manual. Flush with air as necessary. Clean parts in a cleaning fluid and dry. Tighten the filter cartridge after every few cold starts to be sure it stays tight. To adjust timing, loosen the distributor clamp screw and turn the distributor body until timing is correct Fig. Use correct oil for engine.
Connect timing light to number one spark plug. It should need 2 quarts 1. This will agitate water and any excess will be blown out with exhaust gas. Fill to the upper check plug Fig. This Bobcat 600 600D 610 611 service manual comes with images instruction and easy to follow guidance on what particular equipment is needed and how the repairing job is performed. When insulation is broken, install a new plug of correct heat range. The ignition switch must be turned on.
Clean all foreign material from outside of housing. Get this workshop service manual on hand, then can possibly assist you with any type of service and repairs that you may need for your bobcat skid steer loader. Seal it using an industrial cement before tightening bolt. Check tires for wear and pressure. Never service or adjust loader with the engine running unless instructed to do so in the manual. Check fuel pump pressure by installing a tee in the fuel line between fuel pump and carburetor and connecting a gauge to the tee. For eye contact flush well and get immediate medical attention.
If either condition exists, have the regulator adjusted to specifications at an authorized Delco—Remy Service Center. If the button is not down, more adjustment of the excess fuel lever is necessary. You need the parts manual! See our and for details. Start the engine and run it at idle for five minutes while checking for oil leaks at the filter. Make sure the bases of the modules are making good contact with the engine shroud. Connect the other wire to the regulator base ground. The Service Safety Training Course is available from your Bobcat dealer.
Plug should be kept clean both inside and out Fig. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Air removal from fuel lines is necessary after filter service. Turn in to reduce fuel supply. Put a screw driver into hole Fig. It picks up where service manuals leave off. Loosen the stationary contact lock nut and turn screw in or out until contact gap is correct Fig.
Install a longer bolt if no more adjustment can be made. If the readings still differ from the readings listed, replace the part tested. If the alternator does not give at least 14 amps, it is defective and should be serviced at an authorized Delco—Remy Service Center. It is written in the language of a mechanic and may include valuable detailed information such as specifications, torques, ranges, etc. Remove carbon from combustion chambers. When timing is correct, tighten the distributor clamp screw.
Check hydraulic fluid level, engine oil level and fuel supply. Check the operation of the lever by pulling the throttle lever fully backward. If the light does not come on, there is an open circuit between the battery and 3 connector. Many people get this manual and prepared for when the necessary needed. Petter engine uses number 2 diesel fuel. Do not bend the plate so much as to prevent full movement of the fuel rack lever Fig. Inspect the wedges for damage or wear.